RIP and IGRP routing practice exam for Cisco CCNA certification

The Cisco CCNA certification requires that you are completely familiar with RIP and IGRP distance vector routing. CCNA certification practice exams are a great way to prepare for the Cisco CCNA certification and for jobs that will require you to install, maintain, and configure RIP and IGRP routing on Cisco routers and switches. This free practice exam will help you to know the Cisco RIP and IGRP routing well enough that you can productively apply your Cisco RIP and IGRP routing knowledge to any network. The Cisco CCNA certification is an entry level certification which will equip you for the type of work that requires extensive use of RIP and IGRP routing.

New! Transcender e-Learning courses

Answer all questions.
Your score will be calculated out of a total of 25 questions even if they are unanswered.
Unanswered questions will be marked wrong.
Your Name:   
Your Email Address:  Your test results will be emailed to you.
1) Which statement is true?
  1. RIP sends partial routing tables as updates every 60 seconds by default.
  2. RIP sends partial routing tables as updates every 30 seconds by default.
  3. RIP sends full routing tables as updates every 60 seconds by default.
  4. RIP sends full routing tables as updates every 30 seconds by default.
 
2) The maximum hop count of RIP version one is;
  1. 15.
  2. 16.
  3. 255.
  4. 256.
 
3) RIP version one is best suited for;
  1. Networks with large numbers of routers.
  2. Networks that are small.
  3. Networks with slower WAN links.
  4. Networks with faster WAN links.
 
4) Fill in the blank.
Do not capitalize.

To determine the optimal path to a destination network RIP considers  as the deciding criteria.

 

  
5) Select the strictly classful protocol from the list.
  1. EIGRP.
  2. OSPF.
  3. RIP Version two.
  4. RIP Version one.


 
6) RIP uses timeout periods or threshholds that must elapse before it it will take the next course of action. What is the RIP threshhold a router sets because it has not heard any updates about a route.
  1. egg timer
  2. route flush timer
  3. route update timer
  4. route invalid timer
 
7) What is the threshhold called that a router sets to define intervals in which to advertise its routes.
 
  1. egg timer
  2. route flush timer
  3. route update timer
  4. route invalid timer
 
8) What is the threshhold called that a router sets when it informs other routers that a route in its table is going to be eliminated shortly.
  1. egg timer
  2. route flush timer
  3. route update timer
  4. route invalid timer
 
9) A RIP router must have the RIP routing protocol configured as well as;
  1. a process ID.
  2. an autonomous system number.
  3. a network address.
  4. a default route.
 
10) The route invalid timer in relationship to the update timer can best be represented by  which equation?
  1. update timer x 3 = route invalid timer.
  2. route invalid timer x 3 = update timer.
  3. update timer / 3 = route invalid timer.
  4. route flush timer - route invalid timer = update timer.
 
11) RIP has an admnistrative distance of:
 
  1. 5.
  2. 90.
  3. 110.
  4. 120.
 
12) Enter the command that enables RIP on a router.
Do not capitalize or abbreviate.

Router (config)# 
 

  
13) At which prompt would you enter the command that tells RIP to listen for traffic or to route traffic for all nodes between 172.16.1.0 - 172.16.4.0
 
  1. Router #
  2. Router (config-router) #
  3. Router (config) #
  4. Router (config-if) #
 
14) IGRP has a default hop count of:
     
  1. 100.
  2. 15.
  3. 16.
  4. 120.
 
15) IGRP has a default metric based on:
 
  1. administrative distance.
  2. hop count.
  3. Bandwidth and delay.
  4. reliability, MTU and load.
 
16) The default updater timer for IGRP is:
  1. 30.
  2. 60.
  3. 270.
  4. 90.
 
17) How many times the update timer is the invalid timer?
  1. 4.
  2. 2.
  3. 3.
  4. 1.5
 
18) IGRP uses a holdodwn timer to prevent changes in a router's status from being propogated immediately How long is the IGRP holddown timer?.
 
  1. 3 times the update plus 10 seconds.
  2. 4 times the update plus 10 seconds.
  3. 2 times the update plus 10 seconds.
  4. 7 times the update plus 10 seconds.
 
19)  The IGRP flush timers are how many seconds by default?
  1. 6 times the update timer.
  2. 7 times the update timer.
  3. 4 times the holddown timer.
  4. 3 times the invalid timer.
 
20) An IGRP router needs two things to be able to route traffic. One is the IGRP routing protocol, the other is:
     
  1. A network number and process ID.
  2. A default route.
  3. A process ID.
  4. A network number and autonomous system
 
21) Which command will display all network layer address' on each interface and all protocols configured on that router. 
  1. show all protocols.
  2. show ip protocols.
  3. show protocols.
  4. show ip protocol.
 
22) Load balancing is achievable using IGRP over 6 unequal cost links using the variance command. Which additional command tells IGRP to share the load across multiple links inversely proportional to the routing metrics?
  1. traffic share balanced.
  2. traffic-share balanced.
  3. traffic share minimum.
  4. traffic-share minimum.
 
23) Enter the command that will display any RIP updates that are received or sent from the interfaces on the router.
Do not capitalize.

Router # terminal monitor
Router # 
Router #
 

  
24) Enter the command that will cause the router to display any IGRP updates that are received or sent from the ninterfaces on the router.
Do not capitalize.

Router # 
 

    
25) Enter the command that will cause the router to display the incoming IGRP update requests and corresponding replies.
Do not capitalize. 

Router # 
 

    

Use Transcender and save time studying!


Very Good. Now check your score.